DIY HHO TORCH PDF

Hydrogen water torches are similar to blow torches, but they work at much higher temperatures. One of the major advantages of using a. DIY HHO Torch (Water Torch) for Only $4: Introduction: In this Instructable I will show you how to make a simple, cheap and effective HHO torch that can melt sm. Introduction: In this Instructable I will show you how to make a simple, cheap and effective HHO torch that can melt small pieces of metals like tin cans. This.

Author: Mooguhn Mazurr
Country: Belize
Language: English (Spanish)
Genre: Technology
Published (Last): 6 April 2014
Pages: 408
PDF File Size: 12.59 Mb
ePub File Size: 6.84 Mb
ISBN: 305-2-53896-252-4
Downloads: 42749
Price: Free* [*Free Regsitration Required]
Uploader: Kazragul

I have been using these oxyhydrogen-welders professionally for decades now, they are commercially available and used by countless jewelers and opticians, they are sold under names like aquarius microflame and aquaflame. Which would exert more pressure on the piston. I would imagine that acetylene would work ok, just make sure to use the arrestors.

I love the fact that you only need water to refill the reaction chamber, and never run out of gas. They can melt platinum.

When used properly, there is usually an excess of hydrogen ratio 4: You are commenting using your WordPress. The flame is extremely clean, and you can even use the flame to polish.

Fill the end of your neoprene tube with steel wool packed as tightly as possible, and then insert a basketball pump needle into the tube. Yes — simply change HHO to oxyhydrogen and that would solve it.

Clean the carbon rods with fine grade sandpaper. Like the original poster said, calling it HHO just legitimizes the therm. To submit your questions or ideas, or to simply learn more about Sciencing, contact us here. One of the major advantages of using a hydrogen torch vs. This is a bad idea.

  CONDENSATEUR EVAPORATEUR PDF

DIY HHO Mini Torch

The heat of the hydrogen and oxygen or gasoline, diesel, alcohol or other fuels burning causes all the non-oxygen gasses to expand. Splitting and lighting is super efficient. I suppose most of the heat is probably getting sent out, away from the tip but still.

Wrap a piece of wire around each of the carbon rods, and attach the todch end of each wire to a contact on a 9 volt battery. Fill a glass container with two cups of water and a teaspoon of salt. Carbon Dioxide is only 0.

If you are intent on blowing yourself up with a 2: But HHO welders do have superpowers, they can melt metal by burning water. Bubbles will start to form in the water.

A Science Project on Magnetic Cars. Seriously, check out the Instructable and see for yourself! When you are togch to use your hydrogen torch, light the end of the basketball pump needle with a match.

How to Make a Hydrogen Torch | Sciencing

I have seriously considered putting a tip cleaner wire for sizing in one hole of a cutting tip and peening the the end down to have a one hole nozzle, due to the cost difference. This allows him to reduce the orifice size down to non-standard sizes which in turn allows him to increase the intensity of his HHO flame.

This guy todch using pure oxygen and hydrogen, premixed.

Structure of a Dry Cell. So what does this get used for? Was once employed in a repair shop that ran a lot of phos-copper brazing in deep slots by hand of course. Insert the carbon rods, with the wires hanging out and the 9 volt battery resting outside the container.

  ASTM C270 PDF

Surprisingly, the smaller needle runs perfectly cool, but the bigger one heats up and starts softening the plastic holder after a while. But yeah, HHO has the tendency to have be correlated with overunity idiots and other physics-challenged people who think that when you turn energy into another form of energy you suddenly have more energy despite the loss of energy when you are converting it.

If you just want a bang, splitting and lighting is best return for gas volume. Leave a Reply Cancel reply Enter your comment here Furthermore, whilst hydrogen is flammable, the siy stoichiometric hydrogen-oxygen mixture produced torcj just allowing the gases produced in the cell at the anode and the cathode to freely mix together is basically a potent pre-mixed explosive ready to detonate, so having that mixture hanging around through the system as opposed to mixing it only right where it burns is relatively dangerous.

Has anyone got a good how to for this idea of using the injection needles? Fill in your details below or click an icon to log in: Notify me of new comments via email.

Well, you can put your safety in his hands if you want.