ALTISTART 46 MANUAL PDF

Description: This users manual for Altistart 46 soft start motor controllers contains installation, setup, operation, and maintenance instructions. User’s manual ATS46, 9/21/18, English, Spanish, French, pdf MB. Data Bulletin. Cross Reference Guide for ALTISTART® 46 Soft Start Motor. User’s manual UNI-TELWAY ATS VW3G, 12/13/17, English, pdf MB. Programming manual ATS VW3G, 12/13/17, English.

Author: Nijas Vudosho
Country: Cyprus
Language: English (Spanish)
Genre: History
Published (Last): 21 November 2005
Pages: 44
PDF File Size: 14.37 Mb
ePub File Size: 5.26 Mb
ISBN: 232-2-85654-859-1
Downloads: 76808
Price: Free* [*Free Regsitration Required]
Uploader: Tautilar

USF power altkstart fault, when start mode is required Up to now experience: Remove the transformer by unscrewing the CHC screws using a 4 mm Allen key.

Altistart 46 Maintenance Manual |

Care should be taken not to pinch the wires when reassembling this part. Conversion instructions for sizes 4 and 5 Remove the cable from the current transformers by cutting the clamps and unscrewing the connection screws on the transformers. Note the location and colour of the wires red wires on Q1: LrF Locked rotor Fault Measurement principle: Assembly size 3 Parts list Interconnection drawing Part 4: Connect the cables to the plug-in units according to the following drawing.

With software version V1.

The table below gives the detailed product references of the equipment necessary, according to the power of the motor in the case of normal duty. Connect the cables to the electronic card observing the labelling and connecting the connectors with 2 wires to the card. To install this software: White wire mark 1: The following instructions have to be performed: Connect the cable with 2 red wires to J42 on the electronic card.

  KSHAMA PRARTHANA DURGA SAPTASHATI IN SANSKRIT PDF

Value kept for the test voltage 2 V AC Seco nd ar y: Replace altistwrt J13 and J14 from the current transformers on the rating card.

Altistart 46 Soft Starters – Documents and Downloads | Schneider Electric

J 43 Conversion instructions for sizes 4 and 5 6 – Wiring the control cables of thyristors J4 to J9. SY3KC Red wire mark 4: V Insulation varnish must comply with U. Expanded polystyrene is not allowed. SY3KC Blue wire mark 3: Fan 2 3 0V 1 8 5W Recommended torque load for screw M4: To reduce the amount of travelling, training courses have been compacted into one or two weeks depending on your initial level.

Altistart-« 46 Soft Start Motor Controllers Users Manual

For floppy disc 2, follow the instructions that will appear on the PC screen. It suits the one used for Altivar tests. OLF acknoledgement, followed by a start request are done as following: White Green Blue Red diagram of the customer terminal block 12 – Remove the four screws attaching the transformer no.

This conversion can only be performed on products dated later than the following weeks: For wiring J12 and J32 use long cables with connectors so that they can be connected altistat the plug-in unit furthest to the left of the starter.

SBS – Hands on experience. Knowledge required – Knowledge of the main applications cooling, pumping, horizontal handling.

Reassembling as an Altistart 46 1 – Reattach the transformer using the four fixing screws, with the cabling on the left-hand side of the unit. The quality of the replacement service is based on stocks constituted at Evreux, in the branches and by the official dealers.

  HOLT CALIFORNIA ALGEBRA 2 TEXTBOOK PDF

Please refer to page 7 for the wiring of the customer terminal block. mabual

External fault order Operating state Up to now experience: A mechanical kit, a VX4G control module and 64 appropriate measurement card corresponding to the alistart of the motor to be started are necessary for the conversion. The position of the blue wires is different on an ATS Care should be taken to ensure that this card is positioned correctly, placing the connectors towards the top of the unit.

Core housing Material U. It requires a fair knowledge of the product and its applications ventilation, pumping, convoying, …. Place it at the top of the bracket, in the correct location.

The wiring is identical for a starter with 6 plug-in units, except that only every other unit is wired. Humidity test mznual to IEC and 3. LT6 algorithm principle re-employed.

For more information, please contact S. Conversion instructions for size 3 9 – Install the connectors in the locations behind the control module of the Altistart according to the markings. SY3CM 14 2 clips: The starter software version can be seen through a window after additional part disconnection.